{"title":"Quinta 1\/48","description":"","products":[{"product_id":"il-2-3d-printed-coloured-interior-on-decal-paper-for-tamiya-kit","title":"IL-2 3D-Printed \u0026 coloured Interior on decal paper (for Tamiya kit)","description":"\u003cp\u003eIL-2 3D-Printed \u0026amp; coloured Interior on decal paper (for Tamiya kit)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQuinta 3D Decals\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e3D-Decal Working Tips\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e- Since 3D-Decals are significantly thicker than traditional ones, we advise to use additional adhesive to put it in place. PVA-based glue is recommended, although Microscale MetalFoil Adhesive, or acrylic lacquer (such as Tamiya X-22 or Future Pledge) can also be successfully used.\u003c\/p\u003e\n\u003cp\u003e- Small parts can also be glued with cyanoacrylate glue. Keep in mind that using such glue requires extra care – accuracy, quickness and careful positioning are required since the drying time for CYA glue is very short. CYA gel – based glues may be used for preference, since they do give user more time to position the part.\u003c\/p\u003e\n\u003cp\u003e!!! Using decal softener solutions (Micro Set\/Sol, Gunze Mr.Decal etc.) is NOT RECOMMENDED! You risk dissolution and damage to the embossed surface, losing the crispness of detail due to its softening.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOperating procedure\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePrepare plastic kit parts for use. In some cases removing the raised details on kit parts may be required (see decal instructions for specifics).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"2\"\u003e\n\u003cli\u003eOptionally, kit plastic parts may be primed or painted to provide better adhesion for 3D-Decal.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"3\"\u003e\n\u003cli\u003eCarefully apply glue to a plastic kit part in a uniform thin layer. When using Microscale Metal Foil Adhesive, make sure it is transparent first, then glue the part.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"4\"\u003e\n\u003cli\u003eSeparate the 3D-Decal part from its paper base, submerging it into warm water (just as you would do with a conventional water-slide decal), then position it uponthe plastic kit part. Give it some _me dry (approx. 20 mins).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"5\"\u003e\n\u003cli\u003eTo ensure extra adhesion, you may want to use cyanoacrylate glue applied to the side of 3D-Decal part. USE CARE! We recommend using bamboo toothpick or thin wire micro-loop for this opera_on. Using the glue tube itself is not recommended. If small elements or seat belts are present in 3D-Decal layout, we recommend using cyanoacrylate glue, or CYA-gel:\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"6\"\u003e\n\u003cli\u003eSqueeze a drop of CYA-glue out of the tube onto a separate surface.\u003c\/li\u003e\n\u003cli\u003eDip a toothpick or wire micro-loop into it. Miniscule drop of glue should remain on a tip of a toothpick.\u003c\/li\u003e\n\u003cli\u003eCarefully put this miniscule drop onto plastic kit part.\u003c\/li\u003e\n\u003cli\u003eSeparate the 3D-Decal part in warm water, then remove water from it with dry napkin (paper or fabric), or dry brush.\u003c\/li\u003e\n\u003cli\u003ePut the 3D-Decal part in its place on the drop of glue (see step 3). Use sharp tweezers, or a needle, or a _p of a modeling knife, or wet brush.\u003c\/li\u003e\n\u003cli\u003eCarefully and quickly position the 3D-Decal part.\u003c\/li\u003e\n\u003c\/ol\u003e\nWe hope you'll have fun and achieve good results with our products.","brand":"Quinta","offers":[{"title":"Default Title","offer_id":39948709167299,"sku":"QD48020","price":9.0,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0518\/7967\/4051\/products\/QD48020IL-2TamiyaCover.jpg?v=1623062355"},{"product_id":"mi-24v-3d-printed-coloured-interior-on-decal-paper-for-zvezda-kit","title":"Mi-24V  3D-Printed \u0026 coloured Interior on decal paper (for Zvezda kit)","description":"\u003cp\u003eMi-24V  3D-Printed \u0026amp; coloured Interior on decal paper (for Zvezda kit)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQuinta 3D Decals\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e3D-Decal Working Tips\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e- Since 3D-Decals are significantly thicker than traditional ones, we advise to use additional adhesive to put it in place. PVA-based glue is recommended, although Microscale MetalFoil Adhesive, or acrylic lacquer (such as Tamiya X-22 or Future Pledge) can also be successfully used.\u003c\/p\u003e\n\u003cp\u003e- Small parts can also be glued with cyanoacrylate glue. Keep in mind that using such glue requires extra care – accuracy, quickness and careful positioning are required since the drying time for CYA glue is very short. CYA gel – based glues may be used for preference, since they do give user more time to position the part.\u003c\/p\u003e\n\u003cp\u003e!!! Using decal softener solutions (Micro Set\/Sol, Gunze Mr.Decal etc.) is NOT RECOMMENDED! You risk dissolution and damage to the embossed surface, losing the crispness of detail due to its softening.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOperating procedure\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePrepare plastic kit parts for use. In some cases removing the raised details on kit parts may be required (see decal instructions for specifics).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"2\"\u003e\n\u003cli\u003eOptionally, kit plastic parts may be primed or painted to provide better adhesion for 3D-Decal.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"3\"\u003e\n\u003cli\u003eCarefully apply glue to a plastic kit part in a uniform thin layer. When using Microscale Metal Foil Adhesive, make sure it is transparent first, then glue the part.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"4\"\u003e\n\u003cli\u003eSeparate the 3D-Decal part from its paper base, submerging it into warm water (just as you would do with a conventional water-slide decal), then position it uponthe plastic kit part. Give it some _me dry (approx. 20 mins).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"5\"\u003e\n\u003cli\u003eTo ensure extra adhesion, you may want to use cyanoacrylate glue applied to the side of 3D-Decal part. USE CARE! We recommend using bamboo toothpick or thin wire micro-loop for this opera_on. Using the glue tube itself is not recommended. If small elements or seat belts are present in 3D-Decal layout, we recommend using cyanoacrylate glue, or CYA-gel:\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"6\"\u003e\n\u003cli\u003eSqueeze a drop of CYA-glue out of the tube onto a separate surface.\u003c\/li\u003e\n\u003cli\u003eDip a toothpick or wire micro-loop into it. Miniscule drop of glue should remain on a tip of a toothpick.\u003c\/li\u003e\n\u003cli\u003eCarefully put this miniscule drop onto plastic kit part.\u003c\/li\u003e\n\u003cli\u003eSeparate the 3D-Decal part in warm water, then remove water from it with dry napkin (paper or fabric), or dry brush.\u003c\/li\u003e\n\u003cli\u003ePut the 3D-Decal part in its place on the drop of glue (see step 3). Use sharp tweezers, or a needle, or a _p of a modeling knife, or wet brush.\u003c\/li\u003e\n\u003cli\u003eCarefully and quickly position the 3D-Decal part.\u003c\/li\u003e\n\u003c\/ol\u003e\nWe hope you'll have fun and achieve good results with our products.","brand":"Quinta","offers":[{"title":"Default Title","offer_id":39948723388611,"sku":"QD48026","price":22.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0518\/7967\/4051\/products\/QD48026Cover.jpg?v=1623062454"},{"product_id":"f-16i-3d-printed-coloured-interior-on-decal-paper-for-hasegawa-kit","title":"F-16I 3D-Printed \u0026 coloured Interior on decal paper (for Hasegawa kit)","description":"\u003cp\u003eF-16I 3D-Printed \u0026amp; coloured Interior on decal paper (for Hasegawa kit)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQuinta 3D Decals\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e3D-Decal Working Tips\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e- Since 3D-Decals are significantly thicker than traditional ones, we advise to use additional adhesive to put it in place. PVA-based glue is recommended, although Microscale MetalFoil Adhesive, or acrylic lacquer (such as Tamiya X-22 or Future Pledge) can also be successfully used.\u003c\/p\u003e\n\u003cp\u003e- Small parts can also be glued with cyanoacrylate glue. Keep in mind that using such glue requires extra care – accuracy, quickness and careful positioning are required since the drying time for CYA glue is very short. CYA gel – based glues may be used for preference, since they do give user more time to position the part.\u003c\/p\u003e\n\u003cp\u003e!!! Using decal softener solutions (Micro Set\/Sol, Gunze Mr.Decal etc.) is NOT RECOMMENDED! You risk dissolution and damage to the embossed surface, losing the crispness of detail due to its softening.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOperating procedure\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePrepare plastic kit parts for use. In some cases removing the raised details on kit parts may be required (see decal instructions for specifics).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"2\"\u003e\n\u003cli\u003eOptionally, kit plastic parts may be primed or painted to provide better adhesion for 3D-Decal.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"3\"\u003e\n\u003cli\u003eCarefully apply glue to a plastic kit part in a uniform thin layer. When using Microscale Metal Foil Adhesive, make sure it is transparent first, then glue the part.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"4\"\u003e\n\u003cli\u003eSeparate the 3D-Decal part from its paper base, submerging it into warm water (just as you would do with a conventional water-slide decal), then position it uponthe plastic kit part. Give it some _me dry (approx. 20 mins).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"5\"\u003e\n\u003cli\u003eTo ensure extra adhesion, you may want to use cyanoacrylate glue applied to the side of 3D-Decal part. USE CARE! We recommend using bamboo toothpick or thin wire micro-loop for this opera_on. Using the glue tube itself is not recommended. If small elements or seat belts are present in 3D-Decal layout, we recommend using cyanoacrylate glue, or CYA-gel:\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"6\"\u003e\n\u003cli\u003eSqueeze a drop of CYA-glue out of the tube onto a separate surface.\u003c\/li\u003e\n\u003cli\u003eDip a toothpick or wire micro-loop into it. Miniscule drop of glue should remain on a tip of a toothpick.\u003c\/li\u003e\n\u003cli\u003eCarefully put this miniscule drop onto plastic kit part.\u003c\/li\u003e\n\u003cli\u003eSeparate the 3D-Decal part in warm water, then remove water from it with dry napkin (paper or fabric), or dry brush.\u003c\/li\u003e\n\u003cli\u003ePut the 3D-Decal part in its place on the drop of glue (see step 3). Use sharp tweezers, or a needle, or a _p of a modeling knife, or wet brush.\u003c\/li\u003e\n\u003cli\u003eCarefully and quickly position the 3D-Decal part.\u003c\/li\u003e\n\u003c\/ol\u003e\nWe hope you'll have fun and achieve good results with our products.","brand":"Quinta","offers":[{"title":"Default Title","offer_id":39948831883459,"sku":"QD48046","price":22.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0518\/7967\/4051\/products\/QD48046NewCover.jpg?v=1623063381"},{"product_id":"f-a-18e-3d-printed-coloured-interior-on-decal-paper-for-hasegawa-kit","title":"F\/A-18E 3D-Printed \u0026 coloured Interior on decal paper (for Hasegawa kit)","description":"\u003cp\u003eF\/A-18E 3D-Printed \u0026amp; coloured Interior on decal paper (for Hasegawa kit)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQuinta 3D Decals\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e3D-Decal Working Tips\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e- Since 3D-Decals are significantly thicker than traditional ones, we advise to use additional adhesive to put it in place. PVA-based glue is recommended, although Microscale MetalFoil Adhesive, or acrylic lacquer (such as Tamiya X-22 or Future Pledge) can also be successfully used.\u003c\/p\u003e\n\u003cp\u003e- Small parts can also be glued with cyanoacrylate glue. Keep in mind that using such glue requires extra care – accuracy, quickness and careful positioning are required since the drying time for CYA glue is very short. CYA gel – based glues may be used for preference, since they do give user more time to position the part.\u003c\/p\u003e\n\u003cp\u003e!!! Using decal softener solutions (Micro Set\/Sol, Gunze Mr.Decal etc.) is NOT RECOMMENDED! You risk dissolution and damage to the embossed surface, losing the crispness of detail due to its softening.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOperating procedure\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePrepare plastic kit parts for use. In some cases removing the raised details on kit parts may be required (see decal instructions for specifics).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"2\"\u003e\n\u003cli\u003eOptionally, kit plastic parts may be primed or painted to provide better adhesion for 3D-Decal.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"3\"\u003e\n\u003cli\u003eCarefully apply glue to a plastic kit part in a uniform thin layer. When using Microscale Metal Foil Adhesive, make sure it is transparent first, then glue the part.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"4\"\u003e\n\u003cli\u003eSeparate the 3D-Decal part from its paper base, submerging it into warm water (just as you would do with a conventional water-slide decal), then position it uponthe plastic kit part. Give it some _me dry (approx. 20 mins).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"5\"\u003e\n\u003cli\u003eTo ensure extra adhesion, you may want to use cyanoacrylate glue applied to the side of 3D-Decal part. USE CARE! We recommend using bamboo toothpick or thin wire micro-loop for this opera_on. Using the glue tube itself is not recommended. If small elements or seat belts are present in 3D-Decal layout, we recommend using cyanoacrylate glue, or CYA-gel:\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"6\"\u003e\n\u003cli\u003eSqueeze a drop of CYA-glue out of the tube onto a separate surface.\u003c\/li\u003e\n\u003cli\u003eDip a toothpick or wire micro-loop into it. Miniscule drop of glue should remain on a tip of a toothpick.\u003c\/li\u003e\n\u003cli\u003eCarefully put this miniscule drop onto plastic kit part.\u003c\/li\u003e\n\u003cli\u003eSeparate the 3D-Decal part in warm water, then remove water from it with dry napkin (paper or fabric), or dry brush.\u003c\/li\u003e\n\u003cli\u003ePut the 3D-Decal part in its place on the drop of glue (see step 3). Use sharp tweezers, or a needle, or a _p of a modeling knife, or wet brush.\u003c\/li\u003e\n\u003cli\u003eCarefully and quickly position the 3D-Decal part.\u003c\/li\u003e\n\u003c\/ol\u003e\nWe hope you'll have fun and achieve good results with our products.","brand":"Quinta","offers":[{"title":"Default Title","offer_id":39948855214275,"sku":"QD48049","price":18.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0518\/7967\/4051\/products\/QD48049Cover.jpg?v=1623063562"},{"product_id":"mig-21pfm-emerald-color-panels-3d-printed-coloured-interior-on-decal-paper-for-eduard-kit","title":"MiG-21PFM  (emerald color panels) 3D-Printed \u0026 coloured Interior on decal paper (for Eduard  kit)","description":"\u003cp\u003eMiG-21PFM  (emerald color panels) 3D-Printed \u0026amp; coloured Interior on decal paper (for Eduard  kit)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQuinta 3D Decals\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e3D-Decal Working Tips\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e- Since 3D-Decals are significantly thicker than traditional ones, we advise to use additional adhesive to put it in place. PVA-based glue is recommended, although Microscale MetalFoil Adhesive, or acrylic lacquer (such as Tamiya X-22 or Future Pledge) can also be successfully used.\u003c\/p\u003e\n\u003cp\u003e- Small parts can also be glued with cyanoacrylate glue. Keep in mind that using such glue requires extra care – accuracy, quickness and careful positioning are required since the drying time for CYA glue is very short. CYA gel – based glues may be used for preference, since they do give user more time to position the part.\u003c\/p\u003e\n\u003cp\u003e!!! Using decal softener solutions (Micro Set\/Sol, Gunze Mr.Decal etc.) is NOT RECOMMENDED! You risk dissolution and damage to the embossed surface, losing the crispness of detail due to its softening.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOperating procedure\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePrepare plastic kit parts for use. In some cases removing the raised details on kit parts may be required (see decal instructions for specifics).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"2\"\u003e\n\u003cli\u003eOptionally, kit plastic parts may be primed or painted to provide better adhesion for 3D-Decal.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"3\"\u003e\n\u003cli\u003eCarefully apply glue to a plastic kit part in a uniform thin layer. When using Microscale Metal Foil Adhesive, make sure it is transparent first, then glue the part.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"4\"\u003e\n\u003cli\u003eSeparate the 3D-Decal part from its paper base, submerging it into warm water (just as you would do with a conventional water-slide decal), then position it uponthe plastic kit part. Give it some _me dry (approx. 20 mins).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"5\"\u003e\n\u003cli\u003eTo ensure extra adhesion, you may want to use cyanoacrylate glue applied to the side of 3D-Decal part. USE CARE! We recommend using bamboo toothpick or thin wire micro-loop for this opera_on. Using the glue tube itself is not recommended. If small elements or seat belts are present in 3D-Decal layout, we recommend using cyanoacrylate glue, or CYA-gel:\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"6\"\u003e\n\u003cli\u003eSqueeze a drop of CYA-glue out of the tube onto a separate surface.\u003c\/li\u003e\n\u003cli\u003eDip a toothpick or wire micro-loop into it. Miniscule drop of glue should remain on a tip of a toothpick.\u003c\/li\u003e\n\u003cli\u003eCarefully put this miniscule drop onto plastic kit part.\u003c\/li\u003e\n\u003cli\u003eSeparate the 3D-Decal part in warm water, then remove water from it with dry napkin (paper or fabric), or dry brush.\u003c\/li\u003e\n\u003cli\u003ePut the 3D-Decal part in its place on the drop of glue (see step 3). Use sharp tweezers, or a needle, or a _p of a modeling knife, or wet brush.\u003c\/li\u003e\n\u003cli\u003eCarefully and quickly position the 3D-Decal part.\u003c\/li\u003e\n\u003c\/ol\u003e\nWe hope you'll have fun and achieve good results with our products.","brand":"Quinta","offers":[{"title":"Default Title","offer_id":39951121285315,"sku":"QD48077","price":20.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0518\/7967\/4051\/products\/QD48077Cover.jpg?v=1623093566"},{"product_id":"fw-190a-4-3d-printed-coloured-interior-on-decal-paper-for-eduard-kit","title":"FW 190A-4 3D-Printed \u0026 coloured Interior on decal paper (for Eduard  kit)","description":"\u003cp\u003eFW 190A-4 3D-Printed \u0026amp; coloured Interior on decal paper (for Eduard  kit)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQuinta 3D Decals\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e3D-Decal Working Tips\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e- Since 3D-Decals are significantly thicker than traditional ones, we advise to use additional adhesive to put it in place. PVA-based glue is recommended, although Microscale MetalFoil Adhesive, or acrylic lacquer (such as Tamiya X-22 or Future Pledge) can also be successfully used.\u003c\/p\u003e\n\u003cp\u003e- Small parts can also be glued with cyanoacrylate glue. Keep in mind that using such glue requires extra care – accuracy, quickness and careful positioning are required since the drying time for CYA glue is very short. CYA gel – based glues may be used for preference, since they do give user more time to position the part.\u003c\/p\u003e\n\u003cp\u003e!!! Using decal softener solutions (Micro Set\/Sol, Gunze Mr.Decal etc.) is NOT RECOMMENDED! You risk dissolution and damage to the embossed surface, losing the crispness of detail due to its softening.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOperating procedure\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePrepare plastic kit parts for use. In some cases removing the raised details on kit parts may be required (see decal instructions for specifics).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"2\"\u003e\n\u003cli\u003eOptionally, kit plastic parts may be primed or painted to provide better adhesion for 3D-Decal.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"3\"\u003e\n\u003cli\u003eCarefully apply glue to a plastic kit part in a uniform thin layer. When using Microscale Metal Foil Adhesive, make sure it is transparent first, then glue the part.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"4\"\u003e\n\u003cli\u003eSeparate the 3D-Decal part from its paper base, submerging it into warm water (just as you would do with a conventional water-slide decal), then position it uponthe plastic kit part. Give it some _me dry (approx. 20 mins).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"5\"\u003e\n\u003cli\u003eTo ensure extra adhesion, you may want to use cyanoacrylate glue applied to the side of 3D-Decal part. USE CARE! We recommend using bamboo toothpick or thin wire micro-loop for this opera_on. Using the glue tube itself is not recommended. If small elements or seat belts are present in 3D-Decal layout, we recommend using cyanoacrylate glue, or CYA-gel:\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"6\"\u003e\n\u003cli\u003eSqueeze a drop of CYA-glue out of the tube onto a separate surface.\u003c\/li\u003e\n\u003cli\u003eDip a toothpick or wire micro-loop into it. Miniscule drop of glue should remain on a tip of a toothpick.\u003c\/li\u003e\n\u003cli\u003eCarefully put this miniscule drop onto plastic kit part.\u003c\/li\u003e\n\u003cli\u003eSeparate the 3D-Decal part in warm water, then remove water from it with dry napkin (paper or fabric), or dry brush.\u003c\/li\u003e\n\u003cli\u003ePut the 3D-Decal part in its place on the drop of glue (see step 3). Use sharp tweezers, or a needle, or a _p of a modeling knife, or wet brush.\u003c\/li\u003e\n\u003cli\u003eCarefully and quickly position the 3D-Decal part.\u003c\/li\u003e\n\u003c\/ol\u003e\nWe hope you'll have fun and achieve good results with our products.","brand":"Quinta","offers":[{"title":"Default Title","offer_id":39951130132675,"sku":"QD48080","price":10.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0518\/7967\/4051\/products\/QD48080Cover.jpg?v=1623093725"},{"product_id":"bf-109g-14-3d-printed-coloured-interior-on-decal-paper-for-eduard-kit","title":"Bf 109G-14 3D-Printed \u0026 coloured Interior on decal paper (for Eduard  kit)","description":"\u003cp\u003e Bf 109G-14 3D-Printed \u0026amp; coloured Interior on decal paper (for Eduard  kit)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQuinta 3D Decals\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e3D-Decal Working Tips\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e- Since 3D-Decals are significantly thicker than traditional ones, we advise to use additional adhesive to put it in place. PVA-based glue is recommended, although Microscale MetalFoil Adhesive, or acrylic lacquer (such as Tamiya X-22 or Future Pledge) can also be successfully used.\u003c\/p\u003e\n\u003cp\u003e- Small parts can also be glued with cyanoacrylate glue. Keep in mind that using such glue requires extra care – accuracy, quickness and careful positioning are required since the drying time for CYA glue is very short. CYA gel – based glues may be used for preference, since they do give user more time to position the part.\u003c\/p\u003e\n\u003cp\u003e!!! Using decal softener solutions (Micro Set\/Sol, Gunze Mr.Decal etc.) is NOT RECOMMENDED! You risk dissolution and damage to the embossed surface, losing the crispness of detail due to its softening.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOperating procedure\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePrepare plastic kit parts for use. In some cases removing the raised details on kit parts may be required (see decal instructions for specifics).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"2\"\u003e\n\u003cli\u003eOptionally, kit plastic parts may be primed or painted to provide better adhesion for 3D-Decal.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"3\"\u003e\n\u003cli\u003eCarefully apply glue to a plastic kit part in a uniform thin layer. When using Microscale Metal Foil Adhesive, make sure it is transparent first, then glue the part.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"4\"\u003e\n\u003cli\u003eSeparate the 3D-Decal part from its paper base, submerging it into warm water (just as you would do with a conventional water-slide decal), then position it uponthe plastic kit part. Give it some _me dry (approx. 20 mins).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"5\"\u003e\n\u003cli\u003eTo ensure extra adhesion, you may want to use cyanoacrylate glue applied to the side of 3D-Decal part. USE CARE! We recommend using bamboo toothpick or thin wire micro-loop for this opera_on. Using the glue tube itself is not recommended. If small elements or seat belts are present in 3D-Decal layout, we recommend using cyanoacrylate glue, or CYA-gel:\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"6\"\u003e\n\u003cli\u003eSqueeze a drop of CYA-glue out of the tube onto a separate surface.\u003c\/li\u003e\n\u003cli\u003eDip a toothpick or wire micro-loop into it. Miniscule drop of glue should remain on a tip of a toothpick.\u003c\/li\u003e\n\u003cli\u003eCarefully put this miniscule drop onto plastic kit part.\u003c\/li\u003e\n\u003cli\u003eSeparate the 3D-Decal part in warm water, then remove water from it with dry napkin (paper or fabric), or dry brush.\u003c\/li\u003e\n\u003cli\u003ePut the 3D-Decal part in its place on the drop of glue (see step 3). Use sharp tweezers, or a needle, or a _p of a modeling knife, or wet brush.\u003c\/li\u003e\n\u003cli\u003eCarefully and quickly position the 3D-Decal part.\u003c\/li\u003e\n\u003c\/ol\u003e\nWe hope you'll have fun and achieve good results with our products.","brand":"Quinta","offers":[{"title":"Default Title","offer_id":39951217033411,"sku":"QD48095","price":8.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0518\/7967\/4051\/products\/QD48095Cover.jpg?v=1623094558"},{"product_id":"bf-109g-6-3d-printed-coloured-interior-on-decal-paper-for-zvezda-kit","title":"Bf 109G-6 3D-Printed \u0026 coloured Interior on decal paper (for Zvezda  kit)","description":"\u003cp\u003e Bf 109G-6 3D-Printed \u0026amp; coloured Interior on decal paper (for Zvezda  kit)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQuinta 3D Decals\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e3D-Decal Working Tips\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e- Since 3D-Decals are significantly thicker than traditional ones, we advise to use additional adhesive to put it in place. PVA-based glue is recommended, although Microscale MetalFoil Adhesive, or acrylic lacquer (such as Tamiya X-22 or Future Pledge) can also be successfully used.\u003c\/p\u003e\n\u003cp\u003e- Small parts can also be glued with cyanoacrylate glue. Keep in mind that using such glue requires extra care – accuracy, quickness and careful positioning are required since the drying time for CYA glue is very short. CYA gel – based glues may be used for preference, since they do give user more time to position the part.\u003c\/p\u003e\n\u003cp\u003e!!! Using decal softener solutions (Micro Set\/Sol, Gunze Mr.Decal etc.) is NOT RECOMMENDED! You risk dissolution and damage to the embossed surface, losing the crispness of detail due to its softening.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOperating procedure\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePrepare plastic kit parts for use. In some cases removing the raised details on kit parts may be required (see decal instructions for specifics).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"2\"\u003e\n\u003cli\u003eOptionally, kit plastic parts may be primed or painted to provide better adhesion for 3D-Decal.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"3\"\u003e\n\u003cli\u003eCarefully apply glue to a plastic kit part in a uniform thin layer. When using Microscale Metal Foil Adhesive, make sure it is transparent first, then glue the part.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"4\"\u003e\n\u003cli\u003eSeparate the 3D-Decal part from its paper base, submerging it into warm water (just as you would do with a conventional water-slide decal), then position it uponthe plastic kit part. Give it some _me dry (approx. 20 mins).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"5\"\u003e\n\u003cli\u003eTo ensure extra adhesion, you may want to use cyanoacrylate glue applied to the side of 3D-Decal part. USE CARE! We recommend using bamboo toothpick or thin wire micro-loop for this opera_on. Using the glue tube itself is not recommended. If small elements or seat belts are present in 3D-Decal layout, we recommend using cyanoacrylate glue, or CYA-gel:\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"6\"\u003e\n\u003cli\u003eSqueeze a drop of CYA-glue out of the tube onto a separate surface.\u003c\/li\u003e\n\u003cli\u003eDip a toothpick or wire micro-loop into it. Miniscule drop of glue should remain on a tip of a toothpick.\u003c\/li\u003e\n\u003cli\u003eCarefully put this miniscule drop onto plastic kit part.\u003c\/li\u003e\n\u003cli\u003eSeparate the 3D-Decal part in warm water, then remove water from it with dry napkin (paper or fabric), or dry brush.\u003c\/li\u003e\n\u003cli\u003ePut the 3D-Decal part in its place on the drop of glue (see step 3). Use sharp tweezers, or a needle, or a _p of a modeling knife, or wet brush.\u003c\/li\u003e\n\u003cli\u003eCarefully and quickly position the 3D-Decal part.\u003c\/li\u003e\n\u003c\/ol\u003e\nWe hope you'll have fun and achieve good results with our products.","brand":"Quinta","offers":[{"title":"Default Title","offer_id":39951222636739,"sku":"QD48104","price":8.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0518\/7967\/4051\/products\/QD48104Cover.jpg?v=1623094673"},{"product_id":"mig-15-bis-3d-printed-coloured-interior-on-decal-paper-for-bronco-kit","title":"MiG-15 bis 3D-Printed \u0026 coloured Interior on decal paper (for Bronco kit)","description":"\u003cp\u003eMiG-15 bis 3D-Printed \u0026amp; coloured Interior on decal paper (for Bronco kit)\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eQuinta 3D Decals\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e3D-Decal Working Tips\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e- Since 3D-Decals are significantly thicker than traditional ones, we advise to use additional adhesive to put it in place. PVA-based glue is recommended, although Microscale MetalFoil Adhesive, or acrylic lacquer (such as Tamiya X-22 or Future Pledge) can also be successfully used.\u003c\/p\u003e\n\u003cp\u003e- Small parts can also be glued with cyanoacrylate glue. Keep in mind that using such glue requires extra care – accuracy, quickness and careful positioning are required since the drying time for CYA glue is very short. CYA gel – based glues may be used for preference, since they do give user more time to position the part.\u003c\/p\u003e\n\u003cp\u003e!!! Using decal softener solutions (Micro Set\/Sol, Gunze Mr.Decal etc.) is NOT RECOMMENDED! You risk dissolution and damage to the embossed surface, losing the crispness of detail due to its softening.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eOperating procedure\u003c\/strong\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003ePrepare plastic kit parts for use. In some cases removing the raised details on kit parts may be required (see decal instructions for specifics).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"2\"\u003e\n\u003cli\u003eOptionally, kit plastic parts may be primed or painted to provide better adhesion for 3D-Decal.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"3\"\u003e\n\u003cli\u003eCarefully apply glue to a plastic kit part in a uniform thin layer. When using Microscale Metal Foil Adhesive, make sure it is transparent first, then glue the part.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"4\"\u003e\n\u003cli\u003eSeparate the 3D-Decal part from its paper base, submerging it into warm water (just as you would do with a conventional water-slide decal), then position it uponthe plastic kit part. Give it some _me dry (approx. 20 mins).\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"5\"\u003e\n\u003cli\u003eTo ensure extra adhesion, you may want to use cyanoacrylate glue applied to the side of 3D-Decal part. USE CARE! We recommend using bamboo toothpick or thin wire micro-loop for this opera_on. Using the glue tube itself is not recommended. If small elements or seat belts are present in 3D-Decal layout, we recommend using cyanoacrylate glue, or CYA-gel:\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003col start=\"6\"\u003e\n\u003cli\u003eSqueeze a drop of CYA-glue out of the tube onto a separate surface.\u003c\/li\u003e\n\u003cli\u003eDip a toothpick or wire micro-loop into it. Miniscule drop of glue should remain on a tip of a toothpick.\u003c\/li\u003e\n\u003cli\u003eCarefully put this miniscule drop onto plastic kit part.\u003c\/li\u003e\n\u003cli\u003eSeparate the 3D-Decal part in warm water, then remove water from it with dry napkin (paper or fabric), or dry brush.\u003c\/li\u003e\n\u003cli\u003ePut the 3D-Decal part in its place on the drop of glue (see step 3). Use sharp tweezers, or a needle, or a _p of a modeling knife, or wet brush.\u003c\/li\u003e\n\u003cli\u003eCarefully and quickly position the 3D-Decal part.\u003c\/li\u003e\n\u003c\/ol\u003e\nWe hope you'll have fun and achieve good results with our products.","brand":"Quinta","offers":[{"title":"Default Title","offer_id":39951244558531,"sku":"QD48137","price":12.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0518\/7967\/4051\/products\/QD48137Cover.jpg?v=1623095054"}],"url":"https:\/\/www.seriousmodels.gr\/collections\/quinta-1-48.oembed","provider":"Serious Models","version":"1.0","type":"link"}